Xerox Phaser8560 MFP Error Codes


Select an Error Code or Type an Error Code to begin searching

Error


Have a better picture? Update the product image. PNG Only. Open a new private window or clear your cache to see the new image.


Xerox Phaser8560 MFP Top Searches

These results are ranked by popularity.

Error
X3D ... X3XDescription: X3D X3E X3F X3K X3L X3M X3N X3P X3Q X3R X3S X3T X3V X3W X3X Tray 3 pick flag timed-out during warm-up. Tray 3 pick flag timed-out during ready state. Tray 3 pick flag timed-out during a fault state. Tray 3 pick flag timed-out during an oil T
34,01XDescription: Ink Level Sense Faults There are two known ways an Ink level sense over-range fault can occur. One fault condition results from an internal short in the sensor or Printhead. In these cases, replacement of the Printhead is required. A more co
E2D, E2E, E2QDescription: Tray 1 width sensor during warm-up. Tray 1 width sensor during operation. Tray 1 width sensor during Tray 1 pick
5,0xx.6xDescription: Y-Axis Sub-System Program Faults A software error has occurred. The following troubleshooting procedure applies to these errors: 5,001.63 Y-Axis sub-system general fault. 5,005.67 Sub-system not in homeless or idle state, software fault. 5,0
11,100.60Description: Electronics Module Temperature Fault The root problem for this error is temperature sensitivity with the power supply’s opto-isolator chips. The following troubleshooting procedure applies to this error: 11,100.60 The system reports an overh

Xerox Phaser8560 MFP Common Errors

The most common error codes.

Error
X3D ... X3XDescription: X3D X3E X3F X3K X3L X3M X3N X3P X3Q X3R X3S X3T X3V X3W X3X Tray 3 pick flag timed-out during warm-up. Tray 3 pick flag timed-out during ready state. Tray 3 pick flag timed-out during a fault state. Tray 3 pick flag timed-out during an oil T
34,01XDescription: Ink Level Sense Faults There are two known ways an Ink level sense over-range fault can occur. One fault condition results from an internal short in the sensor or Printhead. In these cases, replacement of the Printhead is required. A more co
E2D, E2E, E2QDescription: Tray 1 width sensor during warm-up. Tray 1 width sensor during operation. Tray 1 width sensor during Tray 1 pick
5,0xx.6xDescription: Y-Axis Sub-System Program Faults A software error has occurred. The following troubleshooting procedure applies to these errors: 5,001.63 Y-Axis sub-system general fault. 5,005.67 Sub-system not in homeless or idle state, software fault. 5,0
11,100.60Description: Electronics Module Temperature Fault The root problem for this error is temperature sensitivity with the power supply’s opto-isolator chips. The following troubleshooting procedure applies to this error: 11,100.60 The system reports an overh
X3D ... X3XDescription: X3D X3E X3F X3K X3L X3M X3N X3P X3Q X3R X3S X3T X3V X3W X3X Tray 3 pick flag timed-out during warm-up. Tray 3 pick flag timed-out during ready state. Tray 3 pick flag timed-out during a fault state. Tray 3 pick flag timed-out during an oil T
34,01XDescription: Ink Level Sense Faults There are two known ways an Ink level sense over-range fault can occur. One fault condition results from an internal short in the sensor or Printhead. In these cases, replacement of the Printhead is required. A more co
E2D, E2E, E2QDescription: Tray 1 width sensor during warm-up. Tray 1 width sensor during operation. Tray 1 width sensor during Tray 1 pick
5,0xx.6xDescription: Y-Axis Sub-System Program Faults A software error has occurred. The following troubleshooting procedure applies to these errors: 5,001.63 Y-Axis sub-system general fault. 5,005.67 Sub-system not in homeless or idle state, software fault. 5,0
11,100.60Description: Electronics Module Temperature Fault The root problem for this error is temperature sensitivity with the power supply’s opto-isolator chips. The following troubleshooting procedure applies to this error: 11,100.60 The system reports an overh