Select an Error Code or Type an Error Code to begin searching
Error
Xerox WorkCentre 5755 Top Searches
These results are ranked by popularity.
Error
03-395, 03-396, 03-852, 03-853
Description: IOT PWB Fault RAP 03-395 The IOT has cycled without printing. 03-396 The photoreceptor is detected not turning while the laser is on. 03-852 IOT has detected that it is out of timers. 03-853 IOT has detected that it is nearly out of timers.
11-180-171, 11-182-171
Description: HVF BM Exit Jam RAP 11-180-171 The lead edge is late arriving at the BM exit sensor. 11-182-171 The trail edge is late leaving the BM exit sensor.
11-024-110, 11-025-110
Description: Paddle Roll Failure RAP 11-024-110 The paddle is not at the home position. 11-025-110 The paddle fails to rotate. NOTE: The paddle is in the home position when the sensor flag is located between the sensor jaws. If a jam occurs in the compil
08-160, 08-161
Description: Duplex Paper Path Jam Entry RAP 08-160 The lead edge of the first sheet of a job fed into the duplex path failed to actuate the Duplex sensor in the correct time. 08-161 The trail edge is late to the duplex sensor after of the first sheet of
07-360
Description: Tray 4 Elevator Lift Failure Entry RAP 07-360 Tray 4 stack height sensor does not actuate within 7 seconds after the elevator motor is turned on.
Xerox WorkCentre 5755 Common Errors
The most common error codes.
Error
03-395, 03-396, 03-852, 03-853
Description: IOT PWB Fault RAP 03-395 The IOT has cycled without printing. 03-396 The photoreceptor is detected not turning while the laser is on. 03-852 IOT has detected that it is out of timers. 03-853 IOT has detected that it is nearly out of timers.
11-180-171, 11-182-171
Description: HVF BM Exit Jam RAP 11-180-171 The lead edge is late arriving at the BM exit sensor. 11-182-171 The trail edge is late leaving the BM exit sensor.
11-024-110, 11-025-110
Description: Paddle Roll Failure RAP 11-024-110 The paddle is not at the home position. 11-025-110 The paddle fails to rotate. NOTE: The paddle is in the home position when the sensor flag is located between the sensor jaws. If a jam occurs in the compil
08-160, 08-161
Description: Duplex Paper Path Jam Entry RAP 08-160 The lead edge of the first sheet of a job fed into the duplex path failed to actuate the Duplex sensor in the correct time. 08-161 The trail edge is late to the duplex sensor after of the first sheet of
07-360
Description: Tray 4 Elevator Lift Failure Entry RAP 07-360 Tray 4 stack height sensor does not actuate within 7 seconds after the elevator motor is turned on.
03-395, 03-396, 03-852, 03-853
Description: IOT PWB Fault RAP 03-395 The IOT has cycled without printing. 03-396 The photoreceptor is detected not turning while the laser is on. 03-852 IOT has detected that it is out of timers. 03-853 IOT has detected that it is nearly out of timers.
11-180-171, 11-182-171
Description: HVF BM Exit Jam RAP 11-180-171 The lead edge is late arriving at the BM exit sensor. 11-182-171 The trail edge is late leaving the BM exit sensor.
11-024-110, 11-025-110
Description: Paddle Roll Failure RAP 11-024-110 The paddle is not at the home position. 11-025-110 The paddle fails to rotate. NOTE: The paddle is in the home position when the sensor flag is located between the sensor jaws. If a jam occurs in the compil
08-160, 08-161
Description: Duplex Paper Path Jam Entry RAP 08-160 The lead edge of the first sheet of a job fed into the duplex path failed to actuate the Duplex sensor in the correct time. 08-161 The trail edge is late to the duplex sensor after of the first sheet of
07-360
Description: Tray 4 Elevator Lift Failure Entry RAP 07-360 Tray 4 stack height sensor does not actuate within 7 seconds after the elevator motor is turned on.