Select an Error Code or Type an Error Code to begin searching
Error
Xerox WorkCentre 5745 Top Searches
These results are ranked by popularity.
Error
06-020
Description: ROS Motor Failure RAP 06-020. This fault code has two failure modes. 1. The ROS motor ready signal was not received by the IOT PWB within the set time of the ROS being powered on. 2. The IOT PWB recognizes a change of state of the ROS motor
11-396-171 ... 11-399-171
Description: HVF Rear Tamper Tray RAP 11-396-171 The rear tamper tray did not move from the home position. 11-397-171 The rear tamper tray did not return to the home position. 11-398-171 The rear tamper tray did not move from the away position. 11-399-17
03-320 ... 03-324
Description: Single Board Controller PWB to DADH Error RAP 03-320 Communications between the single board controller PWB and the DADH have failed. 03-321 Communications between the single board controller PWB and the DADH are out of sequence. 03-322 The
11-100-120
Description: 1K LCSS Paper Entry RAP 11-100-110 The leading edge of the sheet is late to the entry sensor Q11-100.
10-101A, 10-102A, 10-103A
Description: Lead Edge Late to Fuser Exit Switch RAP (35-55 ppm) 10-101 The lead edge of the paper failed to actuate the fuser exit switch within the correct time after the registration clutch was energized for a simplex sheet. 10-102 The lead edge of th
Xerox WorkCentre 5745 Common Errors
The most common error codes.
Error
06-020
Description: ROS Motor Failure RAP 06-020. This fault code has two failure modes. 1. The ROS motor ready signal was not received by the IOT PWB within the set time of the ROS being powered on. 2. The IOT PWB recognizes a change of state of the ROS motor
11-396-171 ... 11-399-171
Description: HVF Rear Tamper Tray RAP 11-396-171 The rear tamper tray did not move from the home position. 11-397-171 The rear tamper tray did not return to the home position. 11-398-171 The rear tamper tray did not move from the away position. 11-399-17
03-320 ... 03-324
Description: Single Board Controller PWB to DADH Error RAP 03-320 Communications between the single board controller PWB and the DADH have failed. 03-321 Communications between the single board controller PWB and the DADH are out of sequence. 03-322 The
11-100-120
Description: 1K LCSS Paper Entry RAP 11-100-110 The leading edge of the sheet is late to the entry sensor Q11-100.
10-101A, 10-102A, 10-103A
Description: Lead Edge Late to Fuser Exit Switch RAP (35-55 ppm) 10-101 The lead edge of the paper failed to actuate the fuser exit switch within the correct time after the registration clutch was energized for a simplex sheet. 10-102 The lead edge of th
06-020
Description: ROS Motor Failure RAP 06-020. This fault code has two failure modes. 1. The ROS motor ready signal was not received by the IOT PWB within the set time of the ROS being powered on. 2. The IOT PWB recognizes a change of state of the ROS motor
11-396-171 ... 11-399-171
Description: HVF Rear Tamper Tray RAP 11-396-171 The rear tamper tray did not move from the home position. 11-397-171 The rear tamper tray did not return to the home position. 11-398-171 The rear tamper tray did not move from the away position. 11-399-17
03-320 ... 03-324
Description: Single Board Controller PWB to DADH Error RAP 03-320 Communications between the single board controller PWB and the DADH have failed. 03-321 Communications between the single board controller PWB and the DADH are out of sequence. 03-322 The
11-100-120
Description: 1K LCSS Paper Entry RAP 11-100-110 The leading edge of the sheet is late to the entry sensor Q11-100.
10-101A, 10-102A, 10-103A
Description: Lead Edge Late to Fuser Exit Switch RAP (35-55 ppm) 10-101 The lead edge of the paper failed to actuate the fuser exit switch within the correct time after the registration clutch was energized for a simplex sheet. 10-102 The lead edge of th