Select an Error Code or Type an Error Code to begin searching

Error


Have a better picture? Update the product image. PNG Only. Open a new private window or clear your cache to see the new image.


Xerox WorkCentre 5024 Top Searches

These results are ranked by popularity.

Error
005-275, 005-280Description: DADF RAM Test Fail/ DADF EEPROM Fail [DADF RAM Test Fail] The DADF PWB RAM failed during the Read/Write operation. (At Power ON) [DADF EEPROM Fail] Write failure to DADF EEPROM or communication failure with EEPROM was detected.
024-958, 024-959, 024-960Description: MSI/Tray 1/Tray 2 Paper Size Mismatch During Print Job, the paper size settings of the selected Tray is different from the paper size specified for the Job.
074-101Description: Feed Out Sensor 4 On Jam (Tray 4) The Feed Out Sensor 4 did not turn ON within the specified time after the Paper had been fed from Tray 4.
116-323Description: Controller NVM Data Defect Any of the following was detected: • The On Board NVM data of the Controller is corrupted. • The On Board NVM of the Controller is not installed. • Any one of the Print Counter has reached its maximum value. • The
045-310Description: Image Ready Error Unable to send the Image-valid signal cannot within the specified time. NOTE: When the attempt to expand the image has failed, [016-776 Marker Code Detection Fail] occurs after the recover operation.

Xerox WorkCentre 5024 Common Errors

The most common error codes.

Error
005-275, 005-280Description: DADF RAM Test Fail/ DADF EEPROM Fail [DADF RAM Test Fail] The DADF PWB RAM failed during the Read/Write operation. (At Power ON) [DADF EEPROM Fail] Write failure to DADF EEPROM or communication failure with EEPROM was detected.
024-958, 024-959, 024-960Description: MSI/Tray 1/Tray 2 Paper Size Mismatch During Print Job, the paper size settings of the selected Tray is different from the paper size specified for the Job.
074-101Description: Feed Out Sensor 4 On Jam (Tray 4) The Feed Out Sensor 4 did not turn ON within the specified time after the Paper had been fed from Tray 4.
116-323Description: Controller NVM Data Defect Any of the following was detected: • The On Board NVM data of the Controller is corrupted. • The On Board NVM of the Controller is not installed. • Any one of the Print Counter has reached its maximum value. • The
045-310Description: Image Ready Error Unable to send the Image-valid signal cannot within the specified time. NOTE: When the attempt to expand the image has failed, [016-776 Marker Code Detection Fail] occurs after the recover operation.
024-958, 024-959, 024-960Description: MSI/Tray 1/Tray 2 Paper Size Mismatch During Print Job, the paper size settings of the selected Tray is different from the paper size specified for the Job.
074-101Description: Feed Out Sensor 4 On Jam (Tray 4) The Feed Out Sensor 4 did not turn ON within the specified time after the Paper had been fed from Tray 4.
005-275, 005-280Description: DADF RAM Test Fail/ DADF EEPROM Fail [DADF RAM Test Fail] The DADF PWB RAM failed during the Read/Write operation. (At Power ON) [DADF EEPROM Fail] Write failure to DADF EEPROM or communication failure with EEPROM was detected.
116-323Description: Controller NVM Data Defect Any of the following was detected: • The On Board NVM data of the Controller is corrupted. • The On Board NVM of the Controller is not installed. • Any one of the Print Counter has reached its maximum value. • The
077-211Description: 2TM Type Error An unsupported 2TM was detected to be connected. NOTE: If this is already detected, it will be displayed on the UI Panel when a Job is being performed.