Error |
---|
These results are ranked by popularity.
Error | |
---|---|
C9401, C9402 | Description: • C9401: Exposure lamp lighting failure detected • C9402: Exposure LED lighting abnormally • C9401: The intensity of the lamp is not stabilized within a predetermined period of time during the lamp stabilization check process in a lamp warm- |
C0106-163.xx | Description: Tray 3 feeder up/down abnormality. 163.80 The motor (tray 3 pick/lift) does not turn on. 163.81 The motor (tray 3 pick/lift) does not turn off. 163.82 The motor (tray 3 pick/lift) speed did not ramp up to the required level. 163.83 The motor |
CF### | Description: • The machine displays an abort code (F###) on the operation panel as it becomes unable to process tasks properly through its software control. • When the system program is aborted, check the electrical component, unit, option, and connectio |
CD211, CD212 | Description: • CD211: PCI-SDRAM DMA operation failure • CD212: Compression/extraction timeout detection • CD211: Hardware related to the transfer of memory image of the MFP board (MFPB) fails to respond. • CD212: Hardware related to the BTC compression f |
C3822 | Description: Fusing abnormally low temperature. Fuser heater was too cold when page entered fuser nip |
The most common error codes.
Error | |
---|---|
C9401, C9402 | Description: • C9401: Exposure lamp lighting failure detected • C9402: Exposure LED lighting abnormally • C9401: The intensity of the lamp is not stabilized within a predetermined period of time during the lamp stabilization check process in a lamp warm- |
C0106-163.xx | Description: Tray 3 feeder up/down abnormality. 163.80 The motor (tray 3 pick/lift) does not turn on. 163.81 The motor (tray 3 pick/lift) does not turn off. 163.82 The motor (tray 3 pick/lift) speed did not ramp up to the required level. 163.83 The motor |
CF### | Description: • The machine displays an abort code (F###) on the operation panel as it becomes unable to process tasks properly through its software control. • When the system program is aborted, check the electrical component, unit, option, and connectio |
CD211, CD212 | Description: • CD211: PCI-SDRAM DMA operation failure • CD212: Compression/extraction timeout detection • CD211: Hardware related to the transfer of memory image of the MFP board (MFPB) fails to respond. • CD212: Hardware related to the BTC compression f |
C3822 | Description: Fusing abnormally low temperature. Fuser heater was too cold when page entered fuser nip |
C9401, C9402 | Description: • C9401: Exposure lamp lighting failure detected • C9402: Exposure LED lighting abnormally • C9401: The intensity of the lamp is not stabilized within a predetermined period of time during the lamp stabilization check process in a lamp warm- |
C0106-163.xx | Description: Tray 3 feeder up/down abnormality. 163.80 The motor (tray 3 pick/lift) does not turn on. 163.81 The motor (tray 3 pick/lift) does not turn off. 163.82 The motor (tray 3 pick/lift) speed did not ramp up to the required level. 163.83 The motor |
CF### | Description: • The machine displays an abort code (F###) on the operation panel as it becomes unable to process tasks properly through its software control. • When the system program is aborted, check the electrical component, unit, option, and connectio |
CD211, CD212 | Description: • CD211: PCI-SDRAM DMA operation failure • CD212: Compression/extraction timeout detection • CD211: Hardware related to the transfer of memory image of the MFP board (MFPB) fails to respond. • CD212: Hardware related to the BTC compression f |
C3822 | Description: Fusing abnormally low temperature. Fuser heater was too cold when page entered fuser nip |