Select an Error Code or Type an Error Code to begin searching
| Error |
|---|
| Error |
|---|
These results are ranked by popularity.
| Error | |
|---|---|
| SC35-02 | Description: Thermistor /3 (TH3) low temperature detection (software). The TH3 does not get to 50°C when a specified period of time elapses after the main switch (SW1) is turned ON for the fusing ON control. |
| SC76-32 | Description: The shift unit home sensor (PS11) does not turn OFF within a specified period of time after the shift unit motor (M5) of the tandem (2nd) LS turns ON. Or, the PS11 does not turn ON within a specified period of time. |
| SC29-09 | Description: Drum potential sensor (DPS) output abnormality. While in the 0V check of the DPS, more than 100V of the drum surface potential is detected more than 5 times. When the error code is detected 5 times in succession, this error code is displayed |
| SC23-01 | Description: The speed error signal of the toner bottle motor (M6) is checked. An error detection signal is detected twice in succession a specified period of time after the M6 turns ON (the first signal is ignored). |
| SC77-41 | Description: The entrance conveyance motor (M1) detects an error detection signal for a specified period of time in succession. |
The most common error codes.
| Error | |
|---|---|
| SC35-02 | Description: Thermistor /3 (TH3) low temperature detection (software). The TH3 does not get to 50°C when a specified period of time elapses after the main switch (SW1) is turned ON for the fusing ON control. |
| SC76-32 | Description: The shift unit home sensor (PS11) does not turn OFF within a specified period of time after the shift unit motor (M5) of the tandem (2nd) LS turns ON. Or, the PS11 does not turn ON within a specified period of time. |
| SC29-09 | Description: Drum potential sensor (DPS) output abnormality. While in the 0V check of the DPS, more than 100V of the drum surface potential is detected more than 5 times. When the error code is detected 5 times in succession, this error code is displayed |
| SC23-01 | Description: The speed error signal of the toner bottle motor (M6) is checked. An error detection signal is detected twice in succession a specified period of time after the M6 turns ON (the first signal is ignored). |
| SC77-41 | Description: The entrance conveyance motor (M1) detects an error detection signal for a specified period of time in succession. |
| SC35-02 | Description: Thermistor /3 (TH3) low temperature detection (software). The TH3 does not get to 50°C when a specified period of time elapses after the main switch (SW1) is turned ON for the fusing ON control. |
| SC29-09 | Description: Drum potential sensor (DPS) output abnormality. While in the 0V check of the DPS, more than 100V of the drum surface potential is detected more than 5 times. When the error code is detected 5 times in succession, this error code is displayed |
| SC23-01 | Description: The speed error signal of the toner bottle motor (M6) is checked. An error detection signal is detected twice in succession a specified period of time after the M6 turns ON (the first signal is ignored). |
| SC50-02 | Description: Main body drive serial input abnormality 2. In the I/O initial communication check in the printer control board (PRCB) from the power on ACK, a serial data is not received from the main body drive unit within a specified period of time. |
| SC53-16 | Description: The blowout of a fuse for the SD/ CL in the PF is detected 2. The blowout of a fuse for the SD/CL in the PF drive board (PFUDB) is checked. At the start, an error detection signal (blowout of a fuse for the solenoid/motor) is detected. Howev |