These results are ranked by popularity.
Error | |
---|---|
E020-xxD5 | Description: There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction For INTI control (service mode INISET-*) at time of initial setup, the average of the light Ref values is 562 or higher. The ATR sensor is dam |
E5F5-0001 | Description: There is an error in saddle front stapling. The stitching home position sensor does not turn on when the switch motor (front) is rotated in reverse for 0.5 sec or more. The stitch motor (front, M7S) or the stitching home position sensor (fr |
E013-0002 | Description: There is clogging by waste toner. There is a waste toner feedscrew error. The output of the waste toner lock detecting switch (SW14) is '1' for more than 1 sec. |
E540-8003 | Description: upper tray ascent/descent error (Finisher-R1/R2) safety switch activation |
E002-0030 | Description: The rise in the temperature of the fixing assembly is not enough. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4). The AC driver PCB or the DC con |
The most common error codes.
Error | |
---|---|
E020-xxD5 | Description: There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction For INTI control (service mode INISET-*) at time of initial setup, the average of the light Ref values is 562 or higher. The ATR sensor is dam |
E5F5-0001 | Description: There is an error in saddle front stapling. The stitching home position sensor does not turn on when the switch motor (front) is rotated in reverse for 0.5 sec or more. The stitch motor (front, M7S) or the stitching home position sensor (fr |
E013-0002 | Description: There is clogging by waste toner. There is a waste toner feedscrew error. The output of the waste toner lock detecting switch (SW14) is '1' for more than 1 sec. |
E540-8003 | Description: upper tray ascent/descent error (Finisher-R1/R2) safety switch activation |
E002-0030 | Description: The rise in the temperature of the fixing assembly is not enough. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4). The AC driver PCB or the DC con |
E020-xxD5 | Description: There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction For INTI control (service mode INISET-*) at time of initial setup, the average of the light Ref values is 562 or higher. The ATR sensor is dam |
E5F5-0001 | Description: There is an error in saddle front stapling. The stitching home position sensor does not turn on when the switch motor (front) is rotated in reverse for 0.5 sec or more. The stitch motor (front, M7S) or the stitching home position sensor (fr |
E013-0002 | Description: There is clogging by waste toner. There is a waste toner feedscrew error. The output of the waste toner lock detecting switch (SW14) is '1' for more than 1 sec. |
E540-8003 | Description: upper tray ascent/descent error (Finisher-R1/R2) safety switch activation |
E002-0030 | Description: The rise in the temperature of the fixing assembly is not enough. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4). The AC driver PCB or the DC con |