These results are ranked by popularity.
Error | |
---|---|
E002-0008 | Description: The rise in temperature of the fixing unit is inadequate. The output of the non-contact thermistor does not reach 190°C within 180 sec after it has reached 180°C. |
E711-0001 | Description: There is a fault in IPC communication. DADF-K1 There is a fault in data communication. The ADF controller or the reader controller PCB is faulty. The connector between the reader unit and the ADF has poor connection. An error has been detec |
E5F6-0002 | Description: There is a fault in stapling by the saddle paper pushing plate. Saddle Unit The paper pushing plate motor (M8S) or the paper pushing plate home position sensor (PI14S) is faulty. The paper pushing plate home position sensor does not go OFF |
E530-0002 | Description: There is a fault in alignment. Finisher-N1/Saddle Finisher-N2 There is an excess load on the rear alignment motor (M3), rear aligning plate home position sensor (PI6), or rear aligning plate. The aligning plate does not return to its home p |
E110-0210 | Description: The operation of the laser scanner motor is faulty. The rotation of the M laser scanner motor is faulty. The motor lock signal remains in an unlock state for 1 sec or more while the laser scanner motor is in operation. |
The most common error codes.
Error | |
---|---|
E002-0008 | Description: The rise in temperature of the fixing unit is inadequate. The output of the non-contact thermistor does not reach 190°C within 180 sec after it has reached 180°C. |
E711-0001 | Description: There is a fault in IPC communication. DADF-K1 There is a fault in data communication. The ADF controller or the reader controller PCB is faulty. The connector between the reader unit and the ADF has poor connection. An error has been detec |
E5F6-0002 | Description: There is a fault in stapling by the saddle paper pushing plate. Saddle Unit The paper pushing plate motor (M8S) or the paper pushing plate home position sensor (PI14S) is faulty. The paper pushing plate home position sensor does not go OFF |
E530-0002 | Description: There is a fault in alignment. Finisher-N1/Saddle Finisher-N2 There is an excess load on the rear alignment motor (M3), rear aligning plate home position sensor (PI6), or rear aligning plate. The aligning plate does not return to its home p |
E110-0210 | Description: The operation of the laser scanner motor is faulty. The rotation of the M laser scanner motor is faulty. The motor lock signal remains in an unlock state for 1 sec or more while the laser scanner motor is in operation. |
E002-0008 | Description: The rise in temperature of the fixing unit is inadequate. The output of the non-contact thermistor does not reach 190°C within 180 sec after it has reached 180°C. |
E711-0001 | Description: There is a fault in IPC communication. DADF-K1 There is a fault in data communication. The ADF controller or the reader controller PCB is faulty. The connector between the reader unit and the ADF has poor connection. An error has been detec |
E5F6-0002 | Description: There is a fault in stapling by the saddle paper pushing plate. Saddle Unit The paper pushing plate motor (M8S) or the paper pushing plate home position sensor (PI14S) is faulty. The paper pushing plate home position sensor does not go OFF |
E530-0002 | Description: There is a fault in alignment. Finisher-N1/Saddle Finisher-N2 There is an excess load on the rear alignment motor (M3), rear aligning plate home position sensor (PI6), or rear aligning plate. The aligning plate does not return to its home p |
E110-0210 | Description: The operation of the laser scanner motor is faulty. The rotation of the M laser scanner motor is faulty. The motor lock signal remains in an unlock state for 1 sec or more while the laser scanner motor is in operation. |