These results are ranked by popularity.
Error | |
---|---|
E712-0002 | Description: The connector is not connected properly. The ADF 24-V power supply is faulty. The ADF controller PCB is faulty. The reader controller PCB is faulty. The transmission bit is not enabled after a period of 10 sec at the sync register of the IP |
E302-0001 | Description: The CCD/AP PCB is faulty. The wiring is faulty (short circuit, open circuit). The reader controller PCB is faulty. During shading, the reader controller PCB does not end shading in 1 sec. |
E805-0002 | Description: The wiring is faulty (short circuit, open circuit). The feed fan (FM1) is faulty. The heat discharge fan (FM3) is faulty. The DC controller PCB is faulty. While the feed fan is being driven, the clock signal (FM1CLK) does not arrive for 5 s |
E531-0001 | Description: The stapler home position detecting switch (MS7) is faulty. The stapler motor (M6) is faulty. The finisher controller PCB is faulty. The stapler does not leave home position when the stapler motor has been driven for 0.5 sec. |
E5F3-0001 | Description: The alignment home position sensor (PI5S) is faulty. The alignment motor (M5S) is faulty. The saddle stitcher controller PCB is faulty. The alignment plate home position sensor does not turn on when the alignment motor has been driven for 0 |
The most common error codes.
Error | |
---|---|
E712-0002 | Description: The connector is not connected properly. The ADF 24-V power supply is faulty. The ADF controller PCB is faulty. The reader controller PCB is faulty. The transmission bit is not enabled after a period of 10 sec at the sync register of the IP |
E302-0001 | Description: The CCD/AP PCB is faulty. The wiring is faulty (short circuit, open circuit). The reader controller PCB is faulty. During shading, the reader controller PCB does not end shading in 1 sec. |
E805-0002 | Description: The wiring is faulty (short circuit, open circuit). The feed fan (FM1) is faulty. The heat discharge fan (FM3) is faulty. The DC controller PCB is faulty. While the feed fan is being driven, the clock signal (FM1CLK) does not arrive for 5 s |
E531-0001 | Description: The stapler home position detecting switch (MS7) is faulty. The stapler motor (M6) is faulty. The finisher controller PCB is faulty. The stapler does not leave home position when the stapler motor has been driven for 0.5 sec. |
E5F3-0001 | Description: The alignment home position sensor (PI5S) is faulty. The alignment motor (M5S) is faulty. The saddle stitcher controller PCB is faulty. The alignment plate home position sensor does not turn on when the alignment motor has been driven for 0 |
E712-0002 | Description: The connector is not connected properly. The ADF 24-V power supply is faulty. The ADF controller PCB is faulty. The reader controller PCB is faulty. The transmission bit is not enabled after a period of 10 sec at the sync register of the IP |
E302-0001 | Description: The CCD/AP PCB is faulty. The wiring is faulty (short circuit, open circuit). The reader controller PCB is faulty. During shading, the reader controller PCB does not end shading in 1 sec. |
E805-0002 | Description: The wiring is faulty (short circuit, open circuit). The feed fan (FM1) is faulty. The heat discharge fan (FM3) is faulty. The DC controller PCB is faulty. While the feed fan is being driven, the clock signal (FM1CLK) does not arrive for 5 s |
E531-0001 | Description: The stapler home position detecting switch (MS7) is faulty. The stapler motor (M6) is faulty. The finisher controller PCB is faulty. The stapler does not leave home position when the stapler motor has been driven for 0.5 sec. |
E5F3-0001 | Description: The alignment home position sensor (PI5S) is faulty. The alignment motor (M5S) is faulty. The saddle stitcher controller PCB is faulty. The alignment plate home position sensor does not turn on when the alignment motor has been driven for 0 |