These results are ranked by popularity.
Error | |
---|---|
E025-0002 | Description: There is an over-current in the hopper stirring motor (M23)or the black toner supply motor (M25). There is an over-current in the black toner supply motor (M25). |
E5F9-0001 | Description: There is an error in the saddle switch. With any of the following sensor is identifying its respective cover a being closed, the inlet cover switch is identified as being open for 1 sec or more after the start of the initial rotation of the |
E020-xx90 | Description: There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction The result (Sig D) of computation based on the reading of the patch during patch detection (analog)) is lower than 16. |
E592-8001 | Description: There is an error in the punch horizontal registration sensor. (punch unit) There is an error in the light-receiving voltage at time of light emission. (trailing edge sensor) |
E004-0004 | Description: There is an error in the fixing assembly protection circuit. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6). The AC driver PCB or the DC controller PCB has a fault. The |
The most common error codes.
Error | |
---|---|
E025-0002 | Description: There is an over-current in the hopper stirring motor (M23)or the black toner supply motor (M25). There is an over-current in the black toner supply motor (M25). |
E5F9-0001 | Description: There is an error in the saddle switch. With any of the following sensor is identifying its respective cover a being closed, the inlet cover switch is identified as being open for 1 sec or more after the start of the initial rotation of the |
E020-xx90 | Description: There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction The result (Sig D) of computation based on the reading of the patch during patch detection (analog)) is lower than 16. |
E592-8001 | Description: There is an error in the punch horizontal registration sensor. (punch unit) There is an error in the light-receiving voltage at time of light emission. (trailing edge sensor) |
E004-0004 | Description: There is an error in the fixing assembly protection circuit. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6). The AC driver PCB or the DC controller PCB has a fault. The |
E025-0002 | Description: There is an over-current in the hopper stirring motor (M23)or the black toner supply motor (M25). There is an over-current in the black toner supply motor (M25). |
E5F9-0001 | Description: There is an error in the saddle switch. With any of the following sensor is identifying its respective cover a being closed, the inlet cover switch is identified as being open for 1 sec or more after the start of the initial rotation of the |
E020-xx90 | Description: There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction The result (Sig D) of computation based on the reading of the patch during patch detection (analog)) is lower than 16. |
E592-8001 | Description: There is an error in the punch horizontal registration sensor. (punch unit) There is an error in the light-receiving voltage at time of light emission. (trailing edge sensor) |
E004-0004 | Description: There is an error in the fixing assembly protection circuit. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6). The AC driver PCB or the DC controller PCB has a fault. The |