These results are ranked by popularity.
| Error | |
|---|---|
| E032-0001 | Description: The NE connector counter does not operate. There is an open circuit in the line for the count pulse signal. |
| E719-0002 | Description: error in communication with coin vendor/card reader - The IPC cable to the coin vendor is broken and the IPC communication cannot be recovered. - There is an open circuit in the pickup delivery signal line. - An improper connection is detec |
| E530-8002 | Description: There is an error in front alignment (finisher R1/R2). The home position sensor does not go on within a specific period of time after the front alignment motor has started to rotate. |
| E020-xx13 | Description: There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction For INIT control (service mode INISET-*) at time of initial setup, the Ref value is 960 or higher. The ATR sensor is damaged or has an open ci |
| E003-0051 | Description: After standby, the drop in the temperature of the fixing assembly is excessive. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4). The AC driver PCB |
The most common error codes.
| Error | |
|---|---|
| E032-0001 | Description: The NE connector counter does not operate. There is an open circuit in the line for the count pulse signal. |
| E719-0002 | Description: error in communication with coin vendor/card reader - The IPC cable to the coin vendor is broken and the IPC communication cannot be recovered. - There is an open circuit in the pickup delivery signal line. - An improper connection is detec |
| E530-8002 | Description: There is an error in front alignment (finisher R1/R2). The home position sensor does not go on within a specific period of time after the front alignment motor has started to rotate. |
| E020-xx13 | Description: There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction For INIT control (service mode INISET-*) at time of initial setup, the Ref value is 960 or higher. The ATR sensor is damaged or has an open ci |
| E003-0051 | Description: After standby, the drop in the temperature of the fixing assembly is excessive. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4). The AC driver PCB |
| E032-0001 | Description: The NE connector counter does not operate. There is an open circuit in the line for the count pulse signal. |
| E719-0002 | Description: error in communication with coin vendor/card reader - The IPC cable to the coin vendor is broken and the IPC communication cannot be recovered. - There is an open circuit in the pickup delivery signal line. - An improper connection is detec |
| E530-8002 | Description: There is an error in front alignment (finisher R1/R2). The home position sensor does not go on within a specific period of time after the front alignment motor has started to rotate. |
| E020-xx13 | Description: There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction For INIT control (service mode INISET-*) at time of initial setup, the Ref value is 960 or higher. The ATR sensor is damaged or has an open ci |
| E003-0051 | Description: After standby, the drop in the temperature of the fixing assembly is excessive. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4). The AC driver PCB |
