These results are ranked by popularity.
Error | |
---|---|
E000-0011 | Description: At power-on, the rise in the temperature of the fixing assembly is not high enough. The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact. The AC drive PCB or t |
E197-0002 | Description: There is an error in the communication with the fixing feed PCB. In the course of initializing communication between the DC controller and the fixing/feeding unit, as many as 10 communication errors occur continuously. |
E743-0000 | Description: There is a DDI communication error. There is an SCI error. The reception data is faulty. A reception time-out condition has occurred. An SEQ timeout error has occurred. An SEQ time-out error has occurred. |
E021-0001 | Description: There is an error in the rotation of the developing assembly. The developing rotary home position is not detected. The motor rotates out of sync because of poor torque caused by any of the following: The developing rotary HP sensor is fault |
E5F6-8005 | Description: There is an error in saddle butting. The paper pushing plate leading edge position sensor does not turn on when the paper pushing plate motor has been driven for 0.3 sec or more. The paper pushing plate motor (M8S) or the paper pushing plat |
The most common error codes.
Error | |
---|---|
E000-0011 | Description: At power-on, the rise in the temperature of the fixing assembly is not high enough. The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact. The AC drive PCB or t |
E197-0002 | Description: There is an error in the communication with the fixing feed PCB. In the course of initializing communication between the DC controller and the fixing/feeding unit, as many as 10 communication errors occur continuously. |
E743-0000 | Description: There is a DDI communication error. There is an SCI error. The reception data is faulty. A reception time-out condition has occurred. An SEQ timeout error has occurred. An SEQ time-out error has occurred. |
E021-0001 | Description: There is an error in the rotation of the developing assembly. The developing rotary home position is not detected. The motor rotates out of sync because of poor torque caused by any of the following: The developing rotary HP sensor is fault |
E5F6-8005 | Description: There is an error in saddle butting. The paper pushing plate leading edge position sensor does not turn on when the paper pushing plate motor has been driven for 0.3 sec or more. The paper pushing plate motor (M8S) or the paper pushing plat |
E000-0011 | Description: At power-on, the rise in the temperature of the fixing assembly is not high enough. The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact. The AC drive PCB or t |
E197-0002 | Description: There is an error in the communication with the fixing feed PCB. In the course of initializing communication between the DC controller and the fixing/feeding unit, as many as 10 communication errors occur continuously. |
E743-0000 | Description: There is a DDI communication error. There is an SCI error. The reception data is faulty. A reception time-out condition has occurred. An SEQ timeout error has occurred. An SEQ time-out error has occurred. |
E021-0001 | Description: There is an error in the rotation of the developing assembly. The developing rotary home position is not detected. The motor rotates out of sync because of poor torque caused by any of the following: The developing rotary HP sensor is fault |
E5F6-8005 | Description: There is an error in saddle butting. The paper pushing plate leading edge position sensor does not turn on when the paper pushing plate motor has been driven for 0.3 sec or more. The paper pushing plate motor (M8S) or the paper pushing plat |