These results are ranked by popularity.
Error | |
---|---|
E743-0000 | Description: There is a DDI communication error. There is an SCI error. The reception data is faulty. A reception time-out condition has occurred. An SEQ timeout error has occurred. An SEQ time-out error has occurred. |
E021-0001 | Description: There is an error in the rotation of the developing assembly. The developing rotary home position is not detected. The motor rotates out of sync because of poor torque caused by any of the following: The developing rotary HP sensor is fault |
E5F6-8005 | Description: There is an error in saddle butting. The paper pushing plate leading edge position sensor does not turn on when the paper pushing plate motor has been driven for 0.3 sec or more. The paper pushing plate motor (M8S) or the paper pushing plat |
E020-xx11 | Description: There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction For INIT control (service mode INISET-*) at time of initial setup, the Ref value is lower than 62. The ATR sensor is damaged or has an open ci |
E590-8001 | Description: There is an error in the punch motor. (punch unit) The punching home position sensor is not detected when the punch motor has been driven for 200 msec. |
The most common error codes.
Error | |
---|---|
E743-0000 | Description: There is a DDI communication error. There is an SCI error. The reception data is faulty. A reception time-out condition has occurred. An SEQ timeout error has occurred. An SEQ time-out error has occurred. |
E021-0001 | Description: There is an error in the rotation of the developing assembly. The developing rotary home position is not detected. The motor rotates out of sync because of poor torque caused by any of the following: The developing rotary HP sensor is fault |
E5F6-8005 | Description: There is an error in saddle butting. The paper pushing plate leading edge position sensor does not turn on when the paper pushing plate motor has been driven for 0.3 sec or more. The paper pushing plate motor (M8S) or the paper pushing plat |
E020-xx11 | Description: There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction For INIT control (service mode INISET-*) at time of initial setup, the Ref value is lower than 62. The ATR sensor is damaged or has an open ci |
E590-8001 | Description: There is an error in the punch motor. (punch unit) The punching home position sensor is not detected when the punch motor has been driven for 200 msec. |
E743-0000 | Description: There is a DDI communication error. There is an SCI error. The reception data is faulty. A reception time-out condition has occurred. An SEQ timeout error has occurred. An SEQ time-out error has occurred. |
E021-0001 | Description: There is an error in the rotation of the developing assembly. The developing rotary home position is not detected. The motor rotates out of sync because of poor torque caused by any of the following: The developing rotary HP sensor is fault |
E5F6-8005 | Description: There is an error in saddle butting. The paper pushing plate leading edge position sensor does not turn on when the paper pushing plate motor has been driven for 0.3 sec or more. The paper pushing plate motor (M8S) or the paper pushing plat |
E020-xx11 | Description: There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction For INIT control (service mode INISET-*) at time of initial setup, the Ref value is lower than 62. The ATR sensor is damaged or has an open ci |
E590-8001 | Description: There is an error in the punch motor. (punch unit) The punching home position sensor is not detected when the punch motor has been driven for 200 msec. |