These results are ranked by popularity.
Error | |
---|---|
E5F2-0002 | Description: There is a saddle guide error. The guide home position sensor does not go off even when the guide motor has been driven for 1 sec. guide motor (M3S), guide home position sensor (PI13S) |
E540-8002 | Description: There is an upper tray ascent/decent error. (finisher) - The dangerous area is reached before the tray 1 paper surface sensor detects paper surface during the paper surface detection operation. - A discontinuous area is detected during tray |
E196-1abb | Description: The EEPROM is faulty. There is a mismatch between the data that has been written in EEPROM and the data that has been read. (a: chip No. 0 through 5; bb: chip faulty address) |
E004-0102 | Description: The IH power supply is faulty/the IH control mechanism is faulty. After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR) The IH current is faulty. (current leakage) |
E719-0003 | Description: There is a fault in the coin vendor. After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR) While a unit price is being obtained at start-up, an error has occurred in the communication with the coin vendor. |
The most common error codes.
Error | |
---|---|
E5F2-0002 | Description: There is a saddle guide error. The guide home position sensor does not go off even when the guide motor has been driven for 1 sec. guide motor (M3S), guide home position sensor (PI13S) |
E540-8002 | Description: There is an upper tray ascent/decent error. (finisher) - The dangerous area is reached before the tray 1 paper surface sensor detects paper surface during the paper surface detection operation. - A discontinuous area is detected during tray |
E196-1abb | Description: The EEPROM is faulty. There is a mismatch between the data that has been written in EEPROM and the data that has been read. (a: chip No. 0 through 5; bb: chip faulty address) |
E004-0102 | Description: The IH power supply is faulty/the IH control mechanism is faulty. After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR) The IH current is faulty. (current leakage) |
E719-0003 | Description: There is a fault in the coin vendor. After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR) While a unit price is being obtained at start-up, an error has occurred in the communication with the coin vendor. |
E5F2-0002 | Description: There is a saddle guide error. The guide home position sensor does not go off even when the guide motor has been driven for 1 sec. guide motor (M3S), guide home position sensor (PI13S) |
E540-8002 | Description: There is an upper tray ascent/decent error. (finisher) - The dangerous area is reached before the tray 1 paper surface sensor detects paper surface during the paper surface detection operation. - A discontinuous area is detected during tray |
E196-1abb | Description: The EEPROM is faulty. There is a mismatch between the data that has been written in EEPROM and the data that has been read. (a: chip No. 0 through 5; bb: chip faulty address) |
E004-0102 | Description: The IH power supply is faulty/the IH control mechanism is faulty. After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR) The IH current is faulty. (current leakage) |
E719-0003 | Description: There is a fault in the coin vendor. After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR) While a unit price is being obtained at start-up, an error has occurred in the communication with the coin vendor. |