Select an Error Code or Type an Error Code to begin searching

Error


Have a better picture? Update the product image. PNG Only. Open a new private window or clear your cache to see the new image.


Canon iR5020 Top Searches

These results are ranked by popularity.

Error
E500-0001Description: The finisher controller PCB is faulty. The DC controller PCB is faulty. The communication between the host machine and the finisher has been interrupted; this error is detected by the host machine.
E315-0007Description: Main controller PCB, Hard disk drive When a start command is seen to the encoder of the compression/ extension element of the main controller, an end interrupt does not occur after 4 sec.
E001-0003Description: The main thermistor (TH1) has a short circuit. The sub thermistor (TH2) has detected overheating. The AC driver is faulty. The DC controller PCB is faulty.The sub thermistor has detected about 236°C or higher. The error must be reset in se
E5F6-0003Description: The paper push-on plate motor clock sensor (PI1S) is faulty. The paper push-on plate leading edge position sensor (PI15S) is faulty. The paper push-on plate home position sensor (PI14S) is faulty. The paper push-on plate motor (M8S) is fault
E602-0001Description: The wiring is faulty (short circuit, open circuit). The hard disk drive is faulty. The main controller PCB is faulty. A mount error was detected when the hard disk was started up from the boot ROM.

Canon iR5020 Common Errors

The most common error codes.

Error
E500-0001Description: The finisher controller PCB is faulty. The DC controller PCB is faulty. The communication between the host machine and the finisher has been interrupted; this error is detected by the host machine.
E315-0007Description: Main controller PCB, Hard disk drive When a start command is seen to the encoder of the compression/ extension element of the main controller, an end interrupt does not occur after 4 sec.
E001-0003Description: The main thermistor (TH1) has a short circuit. The sub thermistor (TH2) has detected overheating. The AC driver is faulty. The DC controller PCB is faulty.The sub thermistor has detected about 236°C or higher. The error must be reset in se
E5F6-0003Description: The paper push-on plate motor clock sensor (PI1S) is faulty. The paper push-on plate leading edge position sensor (PI15S) is faulty. The paper push-on plate home position sensor (PI14S) is faulty. The paper push-on plate motor (M8S) is fault
E602-0001Description: The wiring is faulty (short circuit, open circuit). The hard disk drive is faulty. The main controller PCB is faulty. A mount error was detected when the hard disk was started up from the boot ROM.
E500-0001Description: The finisher controller PCB is faulty. The DC controller PCB is faulty. The communication between the host machine and the finisher has been interrupted; this error is detected by the host machine.
E315-0007Description: Main controller PCB, Hard disk drive When a start command is seen to the encoder of the compression/ extension element of the main controller, an end interrupt does not occur after 4 sec.
E001-0003Description: The main thermistor (TH1) has a short circuit. The sub thermistor (TH2) has detected overheating. The AC driver is faulty. The DC controller PCB is faulty.The sub thermistor has detected about 236°C or higher. The error must be reset in se
E5F6-0003Description: The paper push-on plate motor clock sensor (PI1S) is faulty. The paper push-on plate leading edge position sensor (PI15S) is faulty. The paper push-on plate home position sensor (PI14S) is faulty. The paper push-on plate motor (M8S) is fault
E602-0001Description: The wiring is faulty (short circuit, open circuit). The hard disk drive is faulty. The main controller PCB is faulty. A mount error was detected when the hard disk was started up from the boot ROM.