These results are ranked by popularity.
Error | |
---|---|
E225-0000 | Description: The scanning lamp (xenon tube) is faulty. The inverter PCB is faulty. The CCD/AP PCB is faulty. The reader controller PCB is faulty. A specific signal level cannot be attained by CCD gain correction at power-on. |
E744-1000 | Description: The boot ROM and the firmware have a mismatch of model or type: at time of start-up, the bottom ROM product name is found to be a mismatch |
E5F9-0003 | Description: The inlet cover switch (MS1S) is faulty. The front cover switch (MS2S) is faulty. The delivery cover switch (MS3S) is faulty. The saddle stitch controller PCB is faulty. When the inlet cover, front cover, and delivery cover are found to be |
E535-0001 | Description: The swing motor clock sensor (PI20) is faulty. The swing guide open sensor (PI18) is faulty. The safety area switch (MS3) is faulty. The swing guide closed detecting switch 2 (MS6) is faulty. The swing motor (M7) is faulty. The finisher cont |
E002-0000 | Description: The main thermistor (TH1) has poor contact or an open circuit. The thermal switch (TP1) has an open circuit. The AC driver is faulty. The DC controller is faulty. The temperature of the upper fixing roller does not reach 100°C within 2 min |
The most common error codes.
Error | |
---|---|
E225-0000 | Description: The scanning lamp (xenon tube) is faulty. The inverter PCB is faulty. The CCD/AP PCB is faulty. The reader controller PCB is faulty. A specific signal level cannot be attained by CCD gain correction at power-on. |
E744-1000 | Description: The boot ROM and the firmware have a mismatch of model or type: at time of start-up, the bottom ROM product name is found to be a mismatch |
E5F9-0003 | Description: The inlet cover switch (MS1S) is faulty. The front cover switch (MS2S) is faulty. The delivery cover switch (MS3S) is faulty. The saddle stitch controller PCB is faulty. When the inlet cover, front cover, and delivery cover are found to be |
E535-0001 | Description: The swing motor clock sensor (PI20) is faulty. The swing guide open sensor (PI18) is faulty. The safety area switch (MS3) is faulty. The swing guide closed detecting switch 2 (MS6) is faulty. The swing motor (M7) is faulty. The finisher cont |
E002-0000 | Description: The main thermistor (TH1) has poor contact or an open circuit. The thermal switch (TP1) has an open circuit. The AC driver is faulty. The DC controller is faulty. The temperature of the upper fixing roller does not reach 100°C within 2 min |
E225-0000 | Description: The scanning lamp (xenon tube) is faulty. The inverter PCB is faulty. The CCD/AP PCB is faulty. The reader controller PCB is faulty. A specific signal level cannot be attained by CCD gain correction at power-on. |
E744-1000 | Description: The boot ROM and the firmware have a mismatch of model or type: at time of start-up, the bottom ROM product name is found to be a mismatch |
E5F9-0003 | Description: The inlet cover switch (MS1S) is faulty. The front cover switch (MS2S) is faulty. The delivery cover switch (MS3S) is faulty. The saddle stitch controller PCB is faulty. When the inlet cover, front cover, and delivery cover are found to be |
E535-0001 | Description: The swing motor clock sensor (PI20) is faulty. The swing guide open sensor (PI18) is faulty. The safety area switch (MS3) is faulty. The swing guide closed detecting switch 2 (MS6) is faulty. The swing motor (M7) is faulty. The finisher cont |
E002-0000 | Description: The main thermistor (TH1) has poor contact or an open circuit. The thermal switch (TP1) has an open circuit. The AC driver is faulty. The DC controller is faulty. The temperature of the upper fixing roller does not reach 100°C within 2 min |