Select an Error Code or Type an Error Code to begin searching

Error


Have a better picture? Update the product image. PNG Only. Open a new private window or clear your cache to see the new image.


Xerox WorkCentre 5890 Top Searches

These results are ranked by popularity.

Error
311-005-00-120, 311-006-00-120Description: Front Tamper Move Failure RAP 311-005-00-120 Front tamper fails to move to the front position. 311-006-00-120 Front tamper fails to move to the rear position.
311-371-00-171 ... 311-377-00-171Description: HVF Stapler Position and Priming RAP 311-371-00-171 The stapler did not move from the home position. 311-372-00-171 The stapler did not return to the home position. 311-373-00-171 The stapler did not enter the mid home position. 311-374-00-1
311J-120Description: 1K LCSS Poor Stacking RAP Use this RAP to find the cause of poor stacking in the 1K LCSS.
374-100-00Description: Tray 4 Elevator Lift Failure RAP 374-100-00 Tray 4 stack height sensor did not actuate within the correct time after the elevator motor turned on. NOTE: Rapid closure of tray 3 when tray 4 is being elevated may cause this fault.
391-060-00Description: HVPS Fault RAP 391-060-00 The HVPS fault sensor has detected a high voltage fault. The HVPS fault will occur when: • The (C) charge high voltage supply has a short or open circuit. • The (G) charge grid high voltage supply has a short or ope

Xerox WorkCentre 5890 Common Errors

The most common error codes.

Error
311-005-00-120, 311-006-00-120Description: Front Tamper Move Failure RAP 311-005-00-120 Front tamper fails to move to the front position. 311-006-00-120 Front tamper fails to move to the rear position.
311-371-00-171 ... 311-377-00-171Description: HVF Stapler Position and Priming RAP 311-371-00-171 The stapler did not move from the home position. 311-372-00-171 The stapler did not return to the home position. 311-373-00-171 The stapler did not enter the mid home position. 311-374-00-1
311J-120Description: 1K LCSS Poor Stacking RAP Use this RAP to find the cause of poor stacking in the 1K LCSS.
374-100-00Description: Tray 4 Elevator Lift Failure RAP 374-100-00 Tray 4 stack height sensor did not actuate within the correct time after the elevator motor turned on. NOTE: Rapid closure of tray 3 when tray 4 is being elevated may cause this fault.
391-060-00Description: HVPS Fault RAP 391-060-00 The HVPS fault sensor has detected a high voltage fault. The HVPS fault will occur when: • The (C) charge high voltage supply has a short or open circuit. • The (G) charge grid high voltage supply has a short or ope
311-371-00-171 ... 311-377-00-171Description: HVF Stapler Position and Priming RAP 311-371-00-171 The stapler did not move from the home position. 311-372-00-171 The stapler did not return to the home position. 311-373-00-171 The stapler did not enter the mid home position. 311-374-00-1
311-005-00-120, 311-006-00-120Description: Front Tamper Move Failure RAP 311-005-00-120 Front tamper fails to move to the front position. 311-006-00-120 Front tamper fails to move to the rear position.
311J-120Description: 1K LCSS Poor Stacking RAP Use this RAP to find the cause of poor stacking in the 1K LCSS.
374-100-00Description: Tray 4 Elevator Lift Failure RAP 374-100-00 Tray 4 stack height sensor did not actuate within the correct time after the elevator motor turned on. NOTE: Rapid closure of tray 3 when tray 4 is being elevated may cause this fault.
391-060-00Description: HVPS Fault RAP 391-060-00 The HVPS fault sensor has detected a high voltage fault. The HVPS fault will occur when: • The (C) charge high voltage supply has a short or open circuit. • The (G) charge grid high voltage supply has a short or ope