Select an Error Code or Type an Error Code to begin searching

Error


Have a better picture? Update the product image. PNG Only. Open a new private window or clear your cache to see the new image.


Ricoh MPC8002SP Top Searches

These results are ranked by popularity.

Error
SC525-01Description: Drawer Unit Lock Motor Error Sensor signal did not change for 3000 msec while the drawer lock motor was running.
SC561-00Description: Sensor 2: Heating Roller Front Disconnection 0 degrees or lower was detected for (t1) seconds consecutively. Number of times: 10 or more D135 (Japan): 50 (seconds) D136 (Japan)/D135 (NA): 50 (seconds) D136 (NA)/D135 (EU)/D136(EU): 50 (second
SC650-13Description: Remote Service Modem Communication Error (RC Gate Type Mwas installed but modem is not present (detected during operation)) • An error related to communication (dialup connection, modem board etc.) using the RC Gate Type M was detected or an
SC725-41Description: Crease Motor Error (D615) • Motor driver detected an error. (SC from the first time)
SC722-20 ... SC722-23Description: SC722-20 B Upper Tray Junction Gate Motor Error (D707) SC722-21 B Stapler Junction Gate Motor Error (D707) SC722-22 B Pre-stack Junction Gate Motor Error (D707) SC722-23 B Pre-stack Paper Stopper Motor Error (D707). • When moving to the home

Ricoh MPC8002SP Common Errors

The most common error codes.

Error
SC525-01Description: Drawer Unit Lock Motor Error Sensor signal did not change for 3000 msec while the drawer lock motor was running.
SC561-00Description: Sensor 2: Heating Roller Front Disconnection 0 degrees or lower was detected for (t1) seconds consecutively. Number of times: 10 or more D135 (Japan): 50 (seconds) D136 (Japan)/D135 (NA): 50 (seconds) D136 (NA)/D135 (EU)/D136(EU): 50 (second
SC650-13Description: Remote Service Modem Communication Error (RC Gate Type Mwas installed but modem is not present (detected during operation)) • An error related to communication (dialup connection, modem board etc.) using the RC Gate Type M was detected or an
SC725-41Description: Crease Motor Error (D615) • Motor driver detected an error. (SC from the first time)
SC722-20 ... SC722-23Description: SC722-20 B Upper Tray Junction Gate Motor Error (D707) SC722-21 B Stapler Junction Gate Motor Error (D707) SC722-22 B Pre-stack Junction Gate Motor Error (D707) SC722-23 B Pre-stack Paper Stopper Motor Error (D707). • When moving to the home
SC920-00 ... SC920-04Description: SC920-00 B Printer application error (No response at PM startup) SC920-01 B Printer application error (Timeout during PM operation) SC920-02 B Printer application error (Unable to obtain work memory) SC920-03 B Printer application error (Una
SC204-01Description: Polygon Motor: XSCRDY Signal Error: Bk. During polygon motor rotation, the XSCRDY signal was inactive (H) for longer than one rotation of the polygon. Details: • Occurs when the PATMOS polygon error determination register detects that the XS
SC412-04Description: LD input current (Vpl) Adjustment Error (Y). Failed to adjust the LD power to the target range: Vpl*± 5V. Details: This SC is issued when the machine fails to adjust the LD power to the target range: Vpl*± 5V during process contol.
SC300-02Description: Charge Roller Power Pack Output Error (C). The interrupt that checks the status of the PCU power pack every 10 ms detected SC signals 15 times consecutively. Details: In case of an overcurrent, the Charge Roller Power Pack outputs SC signals
SC395Description: Drum motor (K) Lock. Error detected by the TDCU. If a command sent from the TDCU indicates an error, the engine issues an SC. ASAP command: Motor lock detection setting value (engine to TDCU): 0x5B See table below for ASAP commands notifying