These results are ranked by popularity.
| Error | |
|---|---|
| E302-0001 | Description: The CCD/AP PCB is faulty. The wiring is faulty (short circuit, open circuit). The reader controller PCB is faulty. During shading, the reader controller PCB does not end shading in 1 sec. |
| E001-0001 | Description: The main thermistor (TH1) has a short circuit. The sub thermistor (TH2) has detected overheating. The AC driver is faulty. The DC controller PCB is faulty. The main thermistor or the sub thermistor has detected about 230°C or higher for 2 s |
| E677-0001 | Description: The various printer board (accessories) are faulty. The main controller PCB is faulty. An error has occurred in the communication between the various printer boards (accessories) and the main controller PCB. |
| E593-0001 | Description: The horizontal registration home position sensor (PI1P) is faulty. The horizontal registration motor (M1P) is faulty. The punch driver PCB is faulty. The puncher does not leave home position when the horizontal registration motor has been d |
| E719-0001 | Description: The wiring is faulty (short circuit, open circuit). The coin vendor is faulty. The main controller PCB is faulty. The communication between the coin vendor and the main controller PCB has been interrupted. The error must be reset in servic |
The most common error codes.
| Error | |
|---|---|
| E302-0001 | Description: The CCD/AP PCB is faulty. The wiring is faulty (short circuit, open circuit). The reader controller PCB is faulty. During shading, the reader controller PCB does not end shading in 1 sec. |
| E001-0001 | Description: The main thermistor (TH1) has a short circuit. The sub thermistor (TH2) has detected overheating. The AC driver is faulty. The DC controller PCB is faulty. The main thermistor or the sub thermistor has detected about 230°C or higher for 2 s |
| E677-0001 | Description: The various printer board (accessories) are faulty. The main controller PCB is faulty. An error has occurred in the communication between the various printer boards (accessories) and the main controller PCB. |
| E593-0001 | Description: The horizontal registration home position sensor (PI1P) is faulty. The horizontal registration motor (M1P) is faulty. The punch driver PCB is faulty. The puncher does not leave home position when the horizontal registration motor has been d |
| E719-0001 | Description: The wiring is faulty (short circuit, open circuit). The coin vendor is faulty. The main controller PCB is faulty. The communication between the coin vendor and the main controller PCB has been interrupted. The error must be reset in servic |
| E302-0001 | Description: The CCD/AP PCB is faulty. The wiring is faulty (short circuit, open circuit). The reader controller PCB is faulty. During shading, the reader controller PCB does not end shading in 1 sec. |
| E001-0001 | Description: The main thermistor (TH1) has a short circuit. The sub thermistor (TH2) has detected overheating. The AC driver is faulty. The DC controller PCB is faulty. The main thermistor or the sub thermistor has detected about 230°C or higher for 2 s |
| E677-0001 | Description: The various printer board (accessories) are faulty. The main controller PCB is faulty. An error has occurred in the communication between the various printer boards (accessories) and the main controller PCB. |
| E593-0001 | Description: The horizontal registration home position sensor (PI1P) is faulty. The horizontal registration motor (M1P) is faulty. The punch driver PCB is faulty. The puncher does not leave home position when the horizontal registration motor has been d |
| E719-0001 | Description: The wiring is faulty (short circuit, open circuit). The coin vendor is faulty. The main controller PCB is faulty. The communication between the coin vendor and the main controller PCB has been interrupted. The error must be reset in servic |
